2020 J.P. Carlton Professional Tree Equipment Wood Chippers 1260 Series (6 In.)

Information

2020 J.P. Carlton Professional Tree Equipment Wood Chippers 1260 Series (6 In.)

The J.P. Carlton 1260 Wood Chipper is an extremely versatile machine. The 1260 is the perfect answer for trimming and pruning crews who aren’t doing the large takedowns, or for crews who load or split their big wood. With its 12" x 6" throat opening, dual top and bottom feed rollers, and high torque feed motors, the J.P. Carlton 1260 will out perform any other 6" capacity machine on the market.

The J.P. Carlton 1260 is designed and built to go out and chip every day. The heavy duty construction of the J.P. Carlton 1260 makes it an ideal rental chipper, able to withstand all the punishment customers can dish out. From its high capacity axle and tires, to its heavy-duty frame the 1260 is built right. J.P. Carlton understands the environment the 1260 must survive in every day. Thoughtful design elements like concealed wiring, integrated manifold hydraulics with electronic control, sliding engine disk engagement, keep the 1260 operating at peak performance year after year. For Durability and Dependability nothing compares to J.P. Carlton.

Features may include:
  • Led Taillights mounted high on the infeed out of harms way. The 1260’s taillights have heavy duty covers for extra protection. All the wiring runs inside the frame to give the machine a neater appearance and keep wires clear of damage.
  • Engine Slide System disengages the engine from the cutter disk. This allows the engine to run without spinning the disk. This system also aids at startup by allowing the engine to spin without the turning the disk, minimizing wear to the starter and allowing the engine to crank over easier and at higher speeds.
  • Imron Paint is applied over an epoxy primer after the surface has been media blasted. This finish is then baked on to give a beautiful lasting finish which resists both corrosion and nicks.
  • Heavy Duty 1 ½ ” Feeder Bar
  • 12" x 6" Feed Opening makes feeding the bigger branches and limb material easy.
  • Heavy Duty 2,000 pound capacity tongue jack
  • Folding Feed Table
  • Swivel Discharge quickly and easily allows the operator to fill chip trucks corner to corner, or direct the chips to a precise place on the lot.
  • Locking Fuel and Hydraulic Tanks are sleekly designed to fit neatly within the confines of the frame. Locking caps prevent vandalism.
  • Also Available with Two Speed Four Wheel Drive Self-Propelled Undercarriage.

Photos

Highlights

  • Bossier City, Louisiana
  • 2020
  • J.P. Carlton Professional Tree Equipment
  • Wood Chippers 1260 Series (6 In.)
  • Sheave: 2B 4.8 | Channel Mnts: Sliding Positive Lock Engagement
  • Available
  • 56 inches
  • 89 inches

Specifications

  • 2020
  • J.P. Carlton Professional Tree Equipment
  • Wood Chippers
  • 1260 Series (6 In.)
  • Brush
  • Sheave: 2B 4.8 | Channel Mnts: Sliding Positive Lock Engagement
  • Vanguard 35 HP V-Twin
  • Horsepower: 35 HP | Maximum RPM: 3600 RPM
  • 53 Ft Lbs
  • 993cc
  • Medium: Forced Air
  • Two Stage Dry Type
  • Engine: Full Flow Spin On | Hydraulic: 10 Micron Return with Suction Strainer
  • AW32
  • Two
  • 85.5 mm
  • 86.5 mm
  • Dexter Torflex 3500-Pound Cap | Mounts: 1/2" Plate
  • 12 Volt
  • 29HVD 650 CCA | Box: Marine Battery Box
  • 205/75R14 Ld Rng C 1760 # @ 50 PSI
  • 205/75R14 Ld Rng C 1760 # @ 50 PSI
  • Cutter Wheel RPM: 1850 Nominal
  • Drive: Live – Driven off engine
  • 5.33 GPM
  • Displacement: .329 in cu/rev | Drive System: Direct Drive off Engine Mount
  • System Relief: 2500 PSI | Hose: 16,000 PSI Burst – Exceeds SAE 100R2
  • Jackshaft Sheave: 2B 9.4 | Cutter Head Shaft: 2 1/2 inches | Disk Shaft: 2 1/2 inches Removable | Knife: 7 1/4" x 4" x 1/2" | Anvil: 3" x 6" x 1/2" AR400 | Chip Throwers: Two 1/4"x 4" x 3"x 9 1/2" long | Throat Opening. 12" x 6" | Main Trailer Tongue: 2" x 4" with 1/4" wall | Main Trailer Frame: 2" x 4" with 1/4" wall
  • Diameter: 26 inches | Thickness: 1 1/2 inches
  • Disk Bearings: 2 inches Tapered Roller | Feed Roller Bearings: 2 inches Tapered Roller | Feed Roller Shaft: 1 1/4 inches | Feed Rollers : Top 10 1/2" x 12" Btm 6 1/2" x 12"
  • 132 inches
  • 89 inches
  • 56 inches
  • 8" Height Adjustable 2″ Bulldog | Plate: 3/4" Plate adjustable 8" Up/Down
  • Fenders: 10 gauge checker plate | Light Brackets: 3/16" with hidden wiring
  • 9 Gallons | Tank: 10 gauge with baffles rubber mtd | Hydraulic Tank: 10 gauge with baffles rubber mtd
  • Hydraulic Tank: 6 Gallons | Engine: 2.3 Quarts
  • 2620 Pounds | Engine: 94 Lbs (43 KG)
  • Jack Stand: 72000 # Cap Screw Type Swing Up | Valve: Series Type | Drive Belt: 2B90 Kevlar Powerband | Clutch: Sliding Positive Lock Engagement | Disk Balance: Precision High Speed Balanced | Number of Knives: 2 | Springs: Two 15" Tight Wound Powder Coated | Slide Bearings. Two 1" Flange Mount | Infeed Chute: 10ga with 1" tube frame | Folding Infeed Tray: 10ga with 1" tube frame | Folding Tray Lock: 3/4" Spring Loaded Pin
  • Autofeed: Digital Fully Adjustable | Feed Rate: 80 Feet Per Minute | Feeder Bar: 1 1/2" OD x 1/8" wall – removable
  • 360 Adjustable Swivel w/Deflector | Discharge Chute: 10 gauge neck with 14 gauge discharge | Lock: 3/4" Spring Loaded Pin